I am currently on 1.4.13. I am seeing an issue with teh first run of an event driven gcode. I have the below code in "run before job". And I am doing a call to START_NO_ABL in my generated gcode. After a power up I always have the same issue in that this code doesn't seem to run. My gcode basically starts doing things after the call, without doing the call. If I stop the print and restart, it works fine and will continue to work fine until another power failure. Sounds like a flag is not being initialized some place.
@func START_WITH_ABL bed filament
M503 ;report Status
M117 Setting up heaters...
M140 S{{local.bed}} ; set bed final temp
M104 S{{local.filament}} ; set extruder final temp
M109 S{{local.filament}} ; wait for extruder final temp
M190 S{{local.bed}} ; wait for bed final temp
M117 Print Starting...
M75 ; Start Print Timer and Engage Fil Sensor if USB Printing
M84 E ; Disable E Motor for probe accuracy on direct drive systems
M117 Antiblob retract...
G92 E0 ; Reset Extruder distance to 0
M117 Homing All...
G28 ; home all axes
M117 Generating mesh...
G29; auto bed leveling
M503 ;Report status
M117 Heaters Recovering...
M420 Z0; Z fade
M900 K0; LA
M140 S{{local.bed}} ; set bed final temp
M104 S{{local.filament}} ; set extruder final temp
M109 S{{local.filament}} ; wait for extruder final temp
M190 S{{local.bed}} ; wait for bed final temp
M117 Purging extruder...
G92 E0 ; reset extruder
G1 Z1.0 F3000 ; move z up little to prevent scratching of surface
G1 X20 Y0.1 Z0.28 F5000.0 ; move to start-line position
G1 E2 F1000 ; de-retract and push ooze
G92 E0 ; reset extruder
G1 X200.0 Y0.1 Z0.28 F1200.0 E9 ; draw 1st line
G92 E0 ; reset extruder
G1 X200 Y2.0 Z0.28 F5000.0 ; move to side a little
G1 X20 Y2.0 Z0.28 E9 F1200.0 ; draw 2nd line
G92 E0 ; reset extruder
G1 E-0.8 F3000; retract to avoid stringing
G92 E0 ; reset extruder
G1 X20.5 E0 F1000.0 ; -0.5mm wipe action to avoid string
G1 X10.0 E0 F1000.0 ; +10mm intro line @ 0.00
G1 E0.6 F1500; de-retract
G92 E0 ; reset extruder
G1 Z1.0 F3000 ; move z up little to prevent scratching of surface
M117 Printing.....
@endfunc
@func START_NO_ABL bed filament
M503 ;report Status
M117 Setting up heaters...
M140 S{{local.bed}} ; set bed final temp
M104 S{{local.filament}} ; set extruder final temp
M109 S{{local.filament}} ; wait for extruder final temp
M190 S{{local.bed}} ; wait for bed final temp
M117 Print Starting...
M75 ; Start Print Timer and Engage Fil Sensor if USB Printing
M84 E ; Disable E Motor for probe accuracy on direct drive systems
M117 Antiblob retract...
G92 E0 ; Reset Extruder distance to 0
M117 Homing All...
G28 ; home all axes
M117 Homing Z Probe...
G28 Z ; home z again
M117 Load Existing mesh...
M420 S1 ;load mesh
M503 ;report Status
M117 Heaters Recovering...
M420 Z0; Z fade
M900 K0; LA
M140 S{{local.bed}} ; set bed final temp
M104 S{{local.filament}} ; set extruder final temp
M109 S{{local.filament}} ; wait for extruder final temp
M190 S{{local.bed}} ; wait for bed final temp
M117 Purging extruder...
G92 E0 ; reset extruder
G1 Z1.0 F3000 ; move z up little to prevent scratching of surface
G1 X20 Y0.1 Z0.28 F5000.0 ; move to start-line position
G1 E2 F1000 ; de-retract and push ooze
G92 E0 ; reset extruder
G1 X200.0 Y0.1 Z0.28 F1200.0 E9 ; draw 1st line
G92 E0 ; reset extruder
G1 X200 Y2.0 Z0.28 F5000.0 ; move to side a little
G1 X20 Y2.0 Z0.28 E9 F1200.0 ; draw 2nd line
G92 E0 ; reset extruder
;G1 E-6 F1500 ;retract to prevent drag line
G1 E-0.8 F3000; retract to avoid stringing
G92 E0 ; reset extruder
G1 X20.5 E0 F1000.0 ; -0.5mm wipe action to avoid string
G1 X10.0 E0 F1000.0 ; +10mm intro line @ 0.00
G1 E0.6 F1500; de-retract
G92 E0 ; reset extruder
G1 Z1.0 F3000 ; move z up little to prevent scratching of surface
M117 Printing.....
@endfunc
