I have been trying to set up auto level my DELTA for about a month and
I am not getting good results. I have gone thru your setup video
on youtube including the tramming .
steps.
M321 S1
home
G131
tram tower slides
G132S1
G32 S2
I am starting to think that the measurements from autolevel are not
being used during printing or manual movement.
See the sections "Using G30 at towers and center" below. Note that
zCorr:0.000 after bed leveling.
All help is appereciated!
G32 S2
11:52:20.531 : Z correction disabled
11:52:20.531 : Info:Autoleveling disabled
11:52:24.166 : Z-probe:19.823 X:-40.00 Y:-40.00
11:52:26.896 : Z-probe:19.997 X:-40.00 Y:-20.00
11:52:29.563 : Z-probe:20.114 X:-40.00 Y:0.00
11:52:32.246 : Z-probe:20.208 X:-40.00 Y:20.00
11:52:35.023 : Z-probe:20.292 X:-40.00 Y:40.00
11:52:39.032 : Z-probe:19.806 X:-20.00 Y:-40.00
11:52:41.762 : Z-probe:19.913 X:-20.00 Y:-20.00
11:52:44.415 : Z-probe:19.954 X:-20.00 Y:0.00
11:52:47.067 : Z-probe:19.940 X:-20.00 Y:20.00
11:52:49.750 : Z-probe:19.903 X:-20.00 Y:40.00
11:52:53.665 : Z-probe:19.850 X:0.00 Y:-40.00
11:52:56.333 : Z-probe:19.816 X:0.00 Y:-20.00
11:52:58.969 : Z-probe:19.803 X:0.00 Y:0.00
11:53:01.621 : Z-probe:19.826 X:0.00 Y:20.00
11:53:04.320 : Z-probe:19.706 X:0.00 Y:40.00
11:53:08.251 : Z-probe:19.997 X:20.00 Y:-40.00
11:53:10.903 : Z-probe:19.877 X:20.00 Y:-20.00
11:53:13.540 : Z-probe:19.806 X:20.00 Y:0.00
11:53:16.192 : Z-probe:19.759 X:20.00 Y:20.00
11:53:18.828 : Z-probe:19.612 X:20.00 Y:40.00
11:53:22.728 : Z-probe:19.622 X:40.00 Y:-40.00
11:53:25.380 : Z-probe:20.000 X:40.00 Y:-20.00
11:53:28.048 : Z-probe:19.913 X:40.00 Y:0.00
11:53:30.684 : Z-probe:19.799 X:40.00 Y:20.00
11:53:33.477 : Z-probe:19.692 X:40.00 Y:40.00
11:53:33.477 : plane: a = -0.0033 b = 0.0001 c = 19.8812
11:53:33.492 : Transformation matrix: 0.999995 0.000000 0.003281
0.000000 1.000000 -0.000145 -0.003281 0.000145 0.999995
11:53:33.492 : Printer height:218.77
11:53:33.492 : CurrentZ:19.88 atZ:20.00
11:53:33.492 : Info:Autoleveling enabled
11:53:34.272 : Z correction enabled
11:53:34.288 : X:40.07 Y:40.00 Z:19.754 E:0.0000
11:53:34.288 : Info:Autoleveling disabled
11:53:38.593 : SelectExtruder:0
11:53:38.593 : X:0.00 Y:0.00 Z:218.764 E:0.0000
Using G30 at towers and center
11:53:38.593 : Info:Autoleveling enabled
11:53:54.739 : Z-probe:9.984 X:-51.96 Y:-30.00 zCorr:0.000
11:53:57.547 : Z-probe:10.088 X:51.96 Y:-30.00 zCorr:0.000
11:54:00.309 : Z-probe:9.605 X:0.00 Y:60.00 zCorr:0.000
11:54:02.617 : Z-probe:9.900 X:0.00 Y:-0.00 zCorr:0.000
G33
11:58:55.056 : Z correction disabled
11:58:55.056 : Reference Z for measurement:20.000
11:58:58.628 : Z-probe:19.746 X:-25.01 Y:-50.00
11:59:01.452 : Z-probe:20.004 X:-0.01 Y:-50.00
11:59:04.213 : Z-probe:19.763 X:24.98 Y:-50.00
11:59:07.224 : Z-probe:20.349 X:49.98 Y:-25.01
11:59:10.110 : Z-probe:20.108 X:24.98 Y:-25.01
11:59:12.933 : Z-probe:19.903 X:-0.01 Y:-25.01
11:59:15.710 : Z-probe:19.876 X:-25.01 Y:-25.01
11:59:18.487 : Z-probe:19.984 X:-50.00 Y:-25.01
11:59:21.310 : Z-probe:20.195 X:-50.00 Y:-0.01
11:59:24.134 : Z-probe:19.997 X:-25.01 Y:-0.01
11:59:26.895 : Z-probe:19.913 X:-0.01 Y:-0.01
11:59:29.812 : Z-probe:19.997 X:24.98 Y:-0.01
11:59:32.698 : Z-probe:20.295 X:49.98 Y:-0.01
11:59:35.475 : Z-probe:20.134 X:49.98 Y:24.98
11:59:38.314 : Z-probe:19.913 X:24.98 Y:24.98
11:59:41.076 : Z-probe:19.897 X:-0.01 Y:24.98
11:59:43.977 : Z-probe:19.980 X:-25.01 Y:24.98
11:59:46.863 : Z-probe:20.818 X:-50.01 Y:24.98
11:59:49.858 : Z-probe:20.017 X:-25.01 Y:49.98
11:59:52.635 : Z-probe:19.953 X:-0.01 Y:49.98
11:59:55.490 : Z-probe:20.017 X:24.98 Y:49.98
11:59:56.348 : Info:Distortion correction matrix:
11:59:56.348 : -76, -2, 5, -2, -3
11:59:56.348 : -81, 2, 10, 9, -13
11:59:56.348 : -19, 0, 9, 0, -29
11:59:56.348 : 2, 12, 10, -11, -35
11:59:56.348 : 36, 25, 0, 24, 3
11:59:56.364 : G33 X-50.00 Y-50.00 Z0.362
11:59:56.364 : G33 X-50.00 Y-25.01 Z0.020
11:59:56.364 : G33 X-50.00 Y-0.01 Z-0.191
11:59:56.364 : G33 X-50.00 Y24.98 Z-0.814
11:59:56.364 : G33 X-50.00 Y49.98 Z-0.764
11:59:56.364 : G33 X-25.01 Y-50.00 Z0.251
11:59:56.364 : G33 X-25.01 Y-25.01 Z0.121
11:59:56.379 : G33 X-25.01 Y-0.01 Z0.000
11:59:56.379 : G33 X-25.01 Y24.98 Z0.020
11:59:56.379 : G33 X-25.01 Y49.98 Z-0.020
11:59:56.379 : G33 X-0.01 Y-50.00 Z0.000
11:59:56.379 : G33 X-0.01 Y-25.01 Z0.101
11:59:56.379 : G33 X-0.01 Y-0.01 Z0.090
11:59:56.379 : G33 X-0.01 Y24.98 Z0.101
11:59:56.395 : G33 X-0.01 Y49.98 Z0.050
11:59:56.395 : G33 X24.98 Y-50.00 Z0.241
11:59:56.395 : G33 X24.98 Y-25.01 Z-0.111
11:59:56.395 : G33 X24.98 Y-0.01 Z0.000
11:59:56.395 : G33 X24.98 Y24.98 Z0.090
11:59:56.395 : G33 X24.98 Y49.98 Z-0.020
11:59:56.395 : G33 X49.98 Y-50.00 Z0.030
11:59:56.410 : G33 X49.98 Y-25.01 Z-0.352
11:59:56.410 : G33 X49.98 Y-0.01 Z-0.291
11:59:56.410 : G33 X49.98 Y24.98 Z-0.131
11:59:56.410 : G33 X49.98 Y49.98 Z-0.030
Using G30 at towers and center
11:59:56.410 : Z correction enabled
12:00:24.007 : Z-probe:9.974 X:-51.96 Y:-30.00 zCorr:0.000
12:00:26.831 : Z-probe:10.037 X:51.96 Y:-30.00 zCorr:0.000
12:00:29.623 : Z-probe:9.625 X:0.00 Y:60.00 zCorr:0.000
12:00:32.025 : Z-probe:9.900 X:0.00 Y:-0.00 zCorr:0.000
